• JP Precision Glass is the leading glass shower doors company in Chicago

Tempered Glass Shower Doors: 5 Safety Facts That Protect Your Family

Tempered glass shower doors on a marble walk-in shower

Tempered glass shower doors are the standard in bathrooms for a good reason. This glass is made to break in a safer way than regular glass. Below, we cover what tempered glass is, why showers need it, and how to tell if your door has it. We install shower glass in Chicago, and these are the facts we share most.

1. What Tempered Glass Is

Tempered glass is glass that has been heat-treated or chemically treated after it is cut. The federal safety standard for glazing, 16 CFR Part 1201, defines it this way. Regular glass, often called annealed glass, does not get this treatment.

The treatment changes how the glass behaves under stress. It also changes what happens if the glass ever breaks. That second part is why it matters so much in a shower.

2. How Tempered Glass Breaks

When highly tempered glass breaks, the whole piece breaks into small particles. Regular glass breaks into long, sharp shards. Small pieces are less likely to cause deep cuts.

A shower is wet and slippery, and people can fall against the glass. That is why safety rules focus on glass in and around showers and tubs.

3. Why Tempered Glass Shower Doors Are Required

A rule from the U.S. Consumer Product Safety Commission covers glass used in shower doors and enclosures. It also covers bathtub doors and enclosures. This federal standard has been in effect since July 6, 1977.

Building codes add their own rules. The 2021 International Residential Code treats glass near a shower or tub as a hazardous location. This applies when the bottom edge of the glass is less than 60 inches above the floor. Glass in these spots must be safety glass, and tempered glass is one type that qualifies.

4. Tempered Glass Can’t Be Cut After It Is Made

Tempered glass cannot be cut, drilled, ground, or polished after treatment without breaking. So every cut, notch, and hinge hole is made before the glass is tempered. Nothing can be trimmed on site.

This is why your shower opening is measured first. Then the glass is made to that exact size. It is also why a cracked panel gets replaced, not repaired.

Tempered glass shower doors on a marble walk-in shower

5. How to Tell If Your Shower Door Is Tempered

Look for a small permanent mark on the glass. The 2021 International Residential Code requires safety glass in hazardous spots to carry one. It names who applied it, the type of glass, and the safety standard it meets.

The mark must be etched, sandblasted, fired, embossed, or made so it can’t be removed without being destroyed. It must also stay visible after the glass is installed. If you can’t find a mark on an older door, have a glass pro take a look.

Signs Your Tempered Glass Shower Doors Need Attention

Tempered glass is strong, but the parts around it still wear. Call a pro if you notice any of these:

  • Cracks or chips in the glass
  • Hinges that sag or feel loose
  • A door that rubs, drags, or won’t close
  • Water leaking past the seal or sweep

If the glass is damaged, it needs a new panel made to size. Our shower door replacement service covers removal of the old door and a custom-fit new one.

Frequently Asked Questions

Are all shower doors made of tempered glass?

Shower doors must use safety glass, and tempered glass is one type that meets the rule. Laminated safety glass is another type. Either way, plain annealed glass is not allowed in these spots.

Can I cut a tempered glass panel to fit my shower?

No, tempered glass can’t be cut after it is made without breaking. The panel has to be made to size from exact measurements of your opening.

Is frosted shower glass also tempered?

Frosted glass in a shower door must still be safety glass, just like clear glass. The frosted finish changes the look, not the safety rule.

Where is the safety mark on shower door glass?

The safety mark is a small permanent label on the glass, such as an etched or sandblasted mark. It must stay visible after installation.

Have a question about the glass in your shower? Call JP Precision Glass at (224) 381-6688 or send us a message.